[Click] click configuration problem
Vaibhave Agarwal
vaibhave at cs.utah.edu
Sun Jul 31 06:06:00 EDT 2005
hi guys
I have been trying to use click (for roofnet) for the first time.
I have got an Atheros chipset card.
I installed click using following config :
./configure --enable-userlevel --enable-wifi --disable-linuxmodule
Then I first tried to use stripped.madifi driver, but when i tried to
load the roofnet configuration:
$conf/wifi/gen_config_roofnet.pl --dev "ath0" | click -
It complained of not finding "ath0raw" device.
ath0raw: unknown interface: No such device
using mode g
using conf/wifi/srcr.click
<stdin>:180: While initializing 'sniff_dev/from_dev :: FromDevice':
ath0raw: SIOCGIFINDEX: No such device
<stdin>:183: While initializing 'sniff_dev/to_dev :: ToDevice':
ath0raw: SIOCGIFINDEX: No such device
Then in one of the mails, I found John Bicket saying that he
had ported everything in the BSD branch of Madwifi and also
added a phony device "ath0raw".
So I tried madwifi-BSD branch this time. It seemed to work better
and it didnt give any errors while loading roofnet configuration
and I got the following:
nodew2:click# ifconfig
ath0 Link encap:Ethernet HWaddr 00:09:5B:93:0B:A4
inet addr:10.1.1.3 Bcast:10.255.255.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:980 dropped:0 overruns:0 frame:956
TX packets:380 errors:78 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:5
RX bytes:0 (0.0 b) TX bytes:463092 (452.2 Kb)
Interrupt:5 Memory:d0895000-d08a5000
ath0raw Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
UP BROADCAST RUNNING NOARP MTU:2312 Metric:1
RX packets:0 errors:980 dropped:0 overruns:0 frame:956
TX packets:380 errors:78 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:200
RX bytes:0 (0.0 b) TX bytes:463092 (452.2 Kb)
srcr Link encap:Point-to-Point Protocol
inet addr:5.147.11.164 P-t-P:5.147.11.164 Mask:255.0.0.0
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:10
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Now, isnt srcr supposed to be BROADCAST interface.
Also ath0raw hwaddr is all zeros.
If I try to execute:
$route add default srcr
It prints the following and scrogs the disk.
>ath0: resetting
>ath0: resetting
>svc: unknown program 100000 (me 100021)
What shall I do to solve this problem?
Am I right in using madwifi-BSD instead of madwifi-stripped?
Any help would be greatly appreciated.
thanks
vaibhave
More information about the click
mailing list