[Click] Re: MAKING A NODE AS GATEWAY!!
gaurav dawra
openapproject at hotmail.com
Fri Jul 2 23:00:03 EDT 2004
Hi John
I tried it TWICE, it didn't work. For the time being TWO HOSTS are involved.
I can ping between two machines through wireless interface , it is working
fine with both running on " click configurations"
GATEWAY NODE:
./conf/gen_config_roofnet.pl --dev "wlan0" --gateway 1 > /click/config
/sbin/iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
echo 1 > /proc/sys/net/ipv4/ip_forward
ROUTING TABLE OF GATEWAY NODE:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
153.90.192.0 * 255.255.248.0 U 0 0 0 eth0
5.0.0.0 * 255.0.0.0 U 0 0 0 srcr
6.0.0.0 * 255.0.0.0 U 0 0 0
wlan0
127.0.0.0 * 255.0.0.0 U 0 0 0 lo
default epgwy192.msu.mo 0.0.0.0 UG 0 0 0 eth0
ETH0 INTERFACE OF GATEWAY NODE:
[root at openap click]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:0D:56:3B:CE:61
inet addr:153.90.196.95 Bcast:153.90.199.255 Mask:255.255.248.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:43576 errors:0 dropped:0 overruns:0 frame:0
TX packets:2041 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:11104147 (10.5 Mb) TX bytes:246566 (240.7 Kb)
Interrupt:11 Base address:0xe000 Memory:faffe000-fafff080
---------------------------------------------------------------------------------
OTHER NODE : DISABLED eth0 on this one
added route srcr as default:
/sbin/route add default srcr
Command: "route"
ROUTING TABLE OF THIS NODE:
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
5.0.0.0 * 255.0.0.0 U 0 0 0 srcr
6.0.0.0 * 255.0.0.0 U 0 0 0
wlan0
127.0.0.0 * 255.0.0.0 U 0 0 0 lo
default * 0.0.0.0 UG 0 0 0
eth0
-------------------------------------------------------------------------------
I am trying to ping the eth0 interface (153.90.196.45)of the GATEWAY
machine!! it didn;t work. Something is wrong in my configuration?, i
followed as suggested by you. I mean as far i understand it should work.
Some more hints?? i guess.
Thanx for all help.
Gaurav
>From: John Bicket <jbicket at amsterdam.lcs.mit.edu>
>To: gaurav dawra <openapproject at hotmail.com>
>CC: click at amsterdam.lcs.mit.edu
>Subject: Re: MAKING A NODE AS GATEWAY!!
>Date: Fri, 2 Jul 2004 16:58:04 -0400
>
>
>Hi Gaurav,
>
>
>On the gateway machine, run this to start the nat:
>
> /sbin/iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
> echo 1 > /proc/sys/net/ipv4/ip_forward
>
>on each other node, add the default route through the srcr interface:
>
>/sbin/route add default srcr
>
>
>If you want to check the default route, run "route -n" - this won't do
>hostname lookups, so it won't hang while the lookup times out.
>That should work - to test it, cat /click/srcr_gw/gateway_stats
>which should show you the gateway's ip, last packet rx from that gw, and
>the metric to the gateway.
>
>Then you should be able to connect to internet hosts through the gateway
>from other nodes.
>
>
>--john
>
>gaurav dawra [openapproject at hotmail.com] wrote:
> >
> >Hi John
> >
> >I need ONE of the node in my network to work as Gateway( I think this
> >functionality is required to access network on the OTHER side of WIRELESS
> >Network ).
> >
> >When i load the "roofnet" configuration using this command:
> >
> >./conf/gen_config_roofnet.pl --dev "wlan0" --gateway 1 > /click/config
> >
> >i believe it is the right use of loading the configuration. If not please
> >suggest. I looked into your scripts to find out about the same and also
> >looked into the configuration file of CLICK in /click/config which is
> >loaded using above command.
> >
> >srcr_gw :: GatewaySelector(ETHTYPE 0x092c,
> > IP 5.35.253.45,
> > ETH 00:09:5B:23:FD:2D,
> > LT srcr_lt,
> > ARP srcr_arp,
> > PERIOD 15,
> > GW false,
> > LM srcr_ett);
> >
> >srcr_set_gw :: SetGateway(SEL srcr_gw);
> >
> ># THIS IS ACTUALLY WORKING WHILE I LOOK INTO T HE /click/config FILE:
> >GATWAY IS SET
> ># AS IT IS LOADING commands IN THE if { }
> > if ($gateway) {
> >
> >print <<EOF;
> > -> gw_outgoing_cl :: IPClassifier(dst host $srcr_ip,
> > -);
> >gw_outgoing_cl[0] -> srcr_host;
> >
> >gw_outgoing_cl[1]
> > -> gw_counter_outgoing :: IPAddressCounter(USE_SRC true)
> > -> srcr_ratemon
> > -> srcr_host;
> > Idle -> [1] srcr_set_gw [1]-> Discard;
> >EOF
> >} else {
> >print <<EOF;
> > -> from_gw_cl :: IPClassifier(src net $srcr_net mask $srcr_nm,
> > -);
> >from_gw_cl[0]
> > -> srcr_ratemon
> > -> srcr_host;
> >
> >from_gw_cl[1]
> >-> [1] srcr_set_gw [1]
> >-> srcr_ratemon;
> >EOF
> >
> >--------------------------------------------------------
> >But How do i test it? I enable another node with "click configuration "
> >without enabling GATEWAY. And disables eth0 of this NODE ONE.
> >
> >There is No default route SET when i look into routing tables. When i
> >execute this command to add default route:
> >
> >route add -net default gw 5.8.11.168 dev srcr
> >
> >So that all the packets pass thru srcr. but it does not add this entry ,
> >again when i type "route" it just displays previous settings and hangs
> >after that.
> >
> >It will be helpful if you can able to send routing table ENTRY of any
> >gateway node of ROOFNET, what is the default being set, is it SRCR or
>ETH0.
> >
> >I spend whole afternoon trying to figure out what exactly can i do to
>test
> >WHETHER SECOND NODE IS WORKING AS GATEWAY or NOT?
> >
> >I think setting default gw : as srcr makes sense to me. What do u think?
> >Any Suggestion?
> >
> >I will draw a picture to explain things better.
> >
> > eth0(SHUT DOWN)<-->|| NODE ONE || <--> wlan0(6.8.11.168)
> >srcr(5.8.11.168)
> >
> >TRYING TO PING ETH0 of SECOND NODE
> >
> > wlan0( 6.35.253.45) srcr (5.35.253.45) <---> || NODE TWO || <--> eth0
> >(153.90.196.95) (TRYING TO PING THIS FROM NODE ONE)
> >
> >I know the obvious problem is the default is not SET in route tables of
> >NODE ONE: "route"
> >Destination Gateway Genmask Flags Metric Ref Use
> >Iface
> >5.0.0.0 * 255.0.0.0 U 0 0 0
>srcr
> >6.0.0.0 * 255.0.0.0 U 0 0 0
> >wlan0
> >127.0.0.0 * 255.0.0.0 U 0 0 0
>lo
> >------------------------------------------------------------------------------------
> >Please Suggest? i hope you will reply soon.
> >
> >--Gaurav
> >
> >>From: John Bicket <jbicket at amsterdam.lcs.mit.edu>
> >>To: gaurav dawra <openapproject at hotmail.com>
> >>CC: click at amsterdam.lcs.mit.edu
> >>Subject: Re: madwifi.stripped works:CUD not PING WLAN0 from other
>machine
> >>Date: Tue, 29 Jun 2004 21:23:16 -0400
> >>
> >>
> >>I am assuming that you have both machines running their own click
> >>configs; Is there anything present in /click/srcr_es/bcast_stats
> >>on either machine?
> >>That should show nodes within one-hop.
> >>
> >>What happens when you run "ping -b 6.255.255.255"?
> >>
> >>
> >>--john
> >>
> >>
> >>gaurav dawra [openapproject at hotmail.com] wrote:
> >>>Hi John--
> >>>
> >>>Thanx for the help it is working , i mean to say that the different
> >>>interfaces including WLAN0 and srcr are up and i can ping to them FROM
> >>the
> >>>same machine(Just to see). But i cannot able to PING the wireless
> >>Interface
> >>>from some OTHER machine.
> >>>
> >>>Machine with madwifiand roofnet configuration :
> >>>
> >>>wlan0:
> >>>[root at localhost root]# ifconfig wlan0
> >>>wlan0 Link encap:Ethernet HWaddr 00:09:5B:23:FD:2D
> >>> inet addr:6.35.253.45 Bcast:6.255.255.255 Mask:255.0.0.0
> >>> UP BROADCAST MULTICAST MTU:1650 Metric:1
> >>> RX packets:13 errors:0 dropped:0 overruns:0 frame:0
> >>> TX packets:1300 errors:0 dropped:0 overruns:0 carrier:0
> >>> collisions:0 txqueuelen:0
> >>> RX bytes:182 (182.0 b) TX bytes:1581432 (1.5 Mb)
> >>> Interrupt:3 Base address:0x100
> >>>[root at localhost root]# ifconfig srcr
> >>>srcr Link encap:Ethernet HWaddr 00:01:02:03:04:05
> >>> inet addr:5.35.253.45 Bcast:5.255.255.255 Mask:255.0.0.0
> >>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> >>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> >>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> >>> collisions:0 txqueuelen:100
> >>> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
> >>>
> >>>---------------------------------------------------------------------------
> >>>
> >>>Other NODE has interface :
> >>>
> >>>wlan0 and eth0:
> >>>
> >>>wlan0:
> >>>inetaddr: 6.35.253.1( i did it statically by modifying ifcfg-wlan0
>file),
> >>>and netmask: 255.0.0.0
> >>>
> >>>Same as the above machine. Everything seems to be fine with route
>tables
> >>on
> >>>both machine.
> >>>
> >>>I reached the same stage earlier also by doing whole roofnet
> >>configuration
> >>>NOT by your suggested steps. BUt i am kind of struck here. HOW DO I
>TEST
> >>>THAT MY WLAN0 and SRCR interface is working, please let me know.
> >>>
> >>>Thanx for help anyways,
> >>>
> >>>Gaurav
> >>>
> >>>
> >>>>From: John Bicket <jbicket at amsterdam.lcs.mit.edu>
> >>>>To: gaurav dawra <openapproject at hotmail.com>
> >>>>CC: click at amsterdam.lcs.mit.edu
> >>>>Subject: Re: [Click] Simple Authenticator:"Click" element Class
> >>>>Date: Tue, 29 Jun 2004 13:52:35 -0400
> >>>>
> >>>>Hi Gaurav,
> >>>>
> >>>>There were a few changes that I just checked in.
> >>>>Try a cvs up -dP and recompile and then try again.
> >>>>
> >>>>--john
> >>>>
> >>>>
> >>>>gaurav dawra [openapproject at hotmail.com] wrote:
> >>>>>Thanx for the help John!!
> >>>>>
> >>>>>Here is one error which i cud not able to understand. FIRST i cud not
> >>>>able
> >>>>>to find the prism2_param script , SO used being provided with
>"roofnet
> >>>>>distribution" in /home/roofnet/bin/ made a small change to script in
> >>>>line
> >>>>>:85
> >>>>>
> >>>>>if ($dev =~ /wlan/) {
> >>>>># JUST GAVE THE PATH TO THE prism2_param directory
> >>>>> system "/home/roofnet/bin/prism2_param $dev pseudo_ibss 1"; # line
> >>85
> >>>>>
> >>>>> system "iwconfig $dev essid $ssid";
> >>>>> system "iwconfig $dev rts off";
> >>>>> system "iwconfig $dev retries 8";
> >>>>> #system "iwconfig $dev txpower 23";
> >>>>># HOSTAP does not support SET TX POWER MODE
> >>>>>}
> >>>>>
> >>>>>
> >>>>>EXECUTED THIS COMMAND:
> >>>>>[root at openap conf]# ./gen_config_roofnet.pl --dev "wlan0" >
> >>/click/config
> >>>>>[root at openap conf]#
> >>>>>DONE but an ERROR
> >>>>>
> >>>>>[root at openap conf]# more /click/errors
> >>>>>line 3: While configuring 'rates :: AvailableRates':
> >>>>> error param DEFAULT 2 4 11 22: must start with ethernet address
> >>>>>Router could not be initialized!
> >>>>>---------------------------------------------------------------------
> >>>>>'dmesg' gives me this :
> >>>>>wifi0: LinkStatus=2 (Disconnected)
> >>>>>wifi0: LinkStatus: BSSID=00:00:00:00:00:00
> >>>>>wifi0: LinkStatus=2 (Disconnected)
> >>>>>wifi0: LinkStatus: BSSID=00:00:00:00:00:00
> >>>>>line 3: While configuring 'rates :: AvailableRates':
> >>>>> error param DEFAULT 2 4 11 22: must start with ethernet address
> >>>>>Router could not be initialized!
> >>>>>chatter: txf :: WifiTXFeedback: couldn't cleanup - 1886544160 !!!
> >>>>>----------------------------------------------------------------------
> >>>>>
> >>>>>Any Ideas? I have never seen this error before. Is your script giving
> >>>>this
> >>>>>error?
> >>>>>
> >>>>>Thanx,
> >>>>>
> >>>>>Gaurav
> >>>>>
> >>>>>
> >>>>>
> >>>>>>From: John Bicket <jbicket at amsterdam.lcs.mit.edu>
> >>>>>>To: gaurav dawra <openapproject at hotmail.com>
> >>>>>>CC: click at amsterdam.lcs.mit.edu
> >>>>>>Subject: Re: [Click] Simple Authenticator:"Click" element Class
> >>>>>>Date: Tue, 29 Jun 2004 11:34:03 -0400
> >>>>>>
> >>>>>>
> >>>>>>Try "gen_config_roofnet.pl" instead of "get_config_roofnet". There
> >>>>>>was a typo in the instructions.
> >>>>>>
> >>>>>>
> >>>>>>--john
> >>>>>>
> >>>>>>gaurav dawra [openapproject at hotmail.com] wrote:
> >>>>>>>Thanx John For the Quick Reply.
> >>>>>>>
> >>>>>>>Here is the command which i executed, i should have mentioned the
> >>>>command
> >>>>>>>and error at first place.
> >>>>>>>
> >>>>>>>/root/click/conf/get_config_roofnet --wlan0 "wlan0" >/click/config
> >>>>>>>bash: /root/click/conf/get_config_roofnet: No such file or
>directory
> >>>>>>>
> >>>>>>>No i am using hostap_cs : here is output of my lsmod:
> >>>>>>>
> >>>>>>>hostap_cs 51188 0 (unused)
> >>>>>>>hostap 111048 0 [hostap_cs]
> >>>>>>>sr_mod 18136 0 (autoclean)
> >>>>>>>input 5728 0 (autoclean)
> >>>>>>>lp 9092 0 (autoclean)
> >>>>>>>parport 37088 0 (autoclean) [lp]
> >>>>>>>ds 8264 1 [hostap_cs]
> >>>>>>>i82365 38016 1
> >>>>>>>
> >>>>>>>JUST SHOWING One those matters.
> >>>>>>>
> >>>>>>>I USED command "gmake" to do compile the CLICK MODULES:
> >>>>>>>
> >>>>>>>Gaurav
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>>From: John Bicket <jbicket at amsterdam.lcs.mit.edu>
> >>>>>>>>To: gaurav dawra <openapproject at hotmail.com>
> >>>>>>>>CC: click at amsterdam.lcs.mit.edu
> >>>>>>>>Subject: Re: [Click] Simple Authenticator:"Click" element Class
> >>>>>>>>Date: Tue, 29 Jun 2004 11:09:29 -0400
> >>>>>>>>
> >>>>>>>>Try replacing "dev" with wlan0, if that device is present after
>you
> >>>>>>>>modprobe hostap_cs. (if you are using a pci card, you might need
>to
> >>>>>>>>modprobe hostap_pci instead).
> >>>>>>>>
> >>>>>>>>--john
> >>>>>>>>
> >>>>>>>>gaurav dawra [openapproject at hotmail.com] wrote:
> >>>>>>>>>Hi john
> >>>>>>>>>
> >>>>>>>>>Today i am trying to compile the LINUX MODULE. Again the problem
>in
> >>>>the
> >>>>>>>>>last step, yes ! there is a perl file. gen_config_roofnet.pl, but
> >>>>after
> >>>>>>>>>compiling the whole click module with
> >>>>>>>>>
> >>>>>>>>>./configure --enable-wifi --with-wifi=/home/madwifi.stripped/
> >>>>>>>>>--enable-linuxmodule --with-linux=/usr/src/linux-2.4.20roof
> >>>>>>>>>--disable-adaptive --disable-userlevel
> >>>>>>>>>
> >>>>>>>>>modprobe hostap_cs
> >>>>>>>>>modprobe ath_pci ( I BELIEVE I DO NOT REQUIRE THIS, I am NOT
>using
> >>>>>>>>atheros
> >>>>>>>>>based cardbus chipset)
> >>>>>>>>>/sbin/insmod CLICKDIR/linuxmodule/proclikefs.o
> >>>>>>>>>/sbin/insmod CLICKDIR/linuxmodule/click.o
> >>>>>>>>>mkdir -p /click
> >>>>>>>>>mount -n -t click none /click
> >>>>>>>>>*******CLICKDIR/conf/get_config_roofnet --dev "dev" >
> >>>>>>/click/config******
> >>>>>>>>>
> >>>>>>>>>IT DID NOT AUTOMATICALLY GENERATED get_config_roofnet. So again
>the
> >>>>>>LAST
> >>>>>>>>>STEP of your instructions is not complete. Am i doing wrong
> >>>>somewhere?
> >>>>>>>>>
> >>>>>>>>>Are we supposed to generate file by running perl script or will
>it
> >>>>>>>>generate
> >>>>>>>>>using "gmake" command after ./configure for CLICK MODULES. Please
> >>let
> >>>>>>me
> >>>>>>>>>know. I will await for your response.
> >>>>>>>>>
> >>>>>>>>>Thanx,
> >>>>>>>>>
> >>>>>>>>>Gaurav
> >>>>>>>>>
> >>>>>>>>>>From: John Bicket <jbicket at amsterdam.lcs.mit.edu>
> >>>>>>>>>>To: gaurav dawra <openapproject at hotmail.com>
> >>>>>>>>>>Subject: Re: [Click] Simple Authenticator:"Click" element Class
> >>>>>>>>>>Date: Mon, 28 Jun 2004 16:26:31 -0400
> >>>>>>>>>>
> >>>>>>>>>>
> >>>>>>>>>>Hi Gaurav,
> >>>>>>>>>>
> >>>>>>>>>>I have updated instructions at
> >>>>>>>>>>http://www.pdos.lcs.mit.edu/~jbicket/madwifi.stripped/
> >>>>>>>>>>about building for roofnet - please let me know if you have
> >>trouble
> >>>>>>>>>>with them.
> >>>>>>>>>>
> >>>>>>>>>>--john
> >>>>>>>>>>
> >>>>>>>>>>
> >>>>>>>>>>John Bicket [jbicket at amsterdam.lcs.mit.edu] wrote:
> >>>>>>>>>>>Hi Guarav,
> >>>>>>>>>>>
> >>>>>>>>>>>SimpleAuthenticator is a click element in the elements/wifi/ap
> >>>>>>>>>>>directory. You probably don't want to be using it with a wlan
> >>>>device,
> >>>>>>>>>>>it only really works with Atheros based chipsets.
> >>>>>>>>>>>
> >>>>>>>>>>>I am currently working on a howto for building a roofnet
> >>>>>>configuration,
> >>>>>>>>>>>I will be done in a day or two and will post it.
> >>>>>>>>>>>
> >>>>>>>>>>>
> >>>>>>>>>>>--john
> >>>>>>>>>>>
> >>>>>>>>>>>
> >>>>>>>>>>>gaurav dawra [openapproject at hotmail.com] wrote:
> >>>>>>>>>>>>Hi
> >>>>>>>>>>>>
> >>>>>>>>>>>>I am have question regarding the element class
> >>>>>>"SimpleAuthenticator",
> >>>>>>>>>>what
> >>>>>>>>>>>>is the functionality. Is it defined in the click software or
>is
> >>it
> >>>>>>>>some
> >>>>>>>>>>>>"user defined". This might be a question which is not very
> >>>>>>appropiate
> >>>>>>>>>>but i
> >>>>>>>>>>>>just need to know is it being defined in the "click software"
>or
> >>>>>>not.
> >>>>>>>>>>>>
> >>>>>>>>>>>>I am using a "config" file from roofnet group(uses CLICK as
> >>>>routing
> >>>>>>>>>>>>software) which defines this element class in their
> >>configuration
> >>>>>>>>file.
> >>>>>>>>>>>>
> >>>>>>>>>>>>pr :: ProbeResponder(INTERVAL 1000,
> >>>>>>>>>>>> SSID "madwifi",
> >>>>>>>>>>>> BSSID $mac,
> >>>>>>>>>>>> CHANNEL 3);
> >>>>>>>>>>>>
> >>>>>>>>>>>> auth :: SimpleAuthenticator(BSSID $mac);
> >>>>>>>>>>>>
> >>>>>>>>>>>>
> >>>>>>>>>>>>
> >>>>>>>>>>>> beacon_source -> output;
> >>>>>>>>>>>> auth -> output;
> >>>>>>>>>>>> ar -> output;
> >>>>>>>>>>>> pr -> output;
> >>>>>>>>>>>>
> >>>>>>>>>>>> management_cl [6] -> Print ("auth") -> auth;
> >>>>>>>>>>>>
> >>>>>>>>>>>>--------------------------------------------------------------------------------------------
> >>>>>>>>>>>>
> >>>>>>>>>>>>But if i delete these lines and install click using
> >>>>"click-install"
> >>>>>>,
> >>>>>>>>>>dmesg
> >>>>>>>>>>>>gives me this error.
> >>>>>>>>>>>>
> >>>>>>>>>>>>Dead loop on virtual device wlan0, fix it urgently!
> >>>>>>>>>>>>Dead loop on virtual device wlan0, fix it urgently!
> >>>>>>>>>>>>---------------------------------------------------------------------------------------------
> >>>>>>>>>>>>
> >>>>>>>>>>>>I searched hours on internet to fine relevance of this error,
> >>if
> >>>>>>any
> >>>>>>>>>>one
> >>>>>>>>>>>>came accross same error please suggest what is going wrong.
> >>>>>>>>>>>>
> >>>>>>>>>>>>[root at localhost roofnet]# iwconfig wlan0
> >>>>>>>>>>>>Warning: Driver for device wlan0 has been compiled with
>version
> >>14
> >>>>>>>>>>>>of Wireless Extension, while this program is using version 15.
> >>>>>>>>>>>>Some things may be broken...
> >>>>>>>>>>>>
> >>>>>>>>>>>>wlan0 IEEE 802.11b ESSID:"roofnet" Nickname:"localhost"
> >>>>>>>>>>>> Mode:Ad-Hoc Frequency:2.422GHz Cell:
> >>00:00:00:00:00:00
> >>>>>>>>>>>> Bit Rate:2Mb/s Sensitivity=1/3
> >>>>>>>>>>>> Retry limit:8 RTS thr:off Fragment thr:off
> >>>>>>>>>>>> Encryption key:off
> >>>>>>>>>>>> Power Management:off
> >>>>>>>>>>>> Link Quality:0/70 Signal level:-73 dBm Noise
> >>level:-73
> >>>>>>dBm
> >>>>>>>>>>>> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid
> >>frag:0
> >>>>>>>>>>>> Tx excessive retries:0 Invalid misc:2 Missed
> >>beacon:0
> >>>>>>>>>>>>
> >>>>>>>>>>>>-----------------------------------------------------------------------------------------------
> >>>>>>>>>>>>I am loading this "configuration" file from roofnet to
> >>understand
> >>>>>>>>better
> >>>>>>>>>>>>the functionality of "click" routing software. I also tried
>few
> >>>>>>>>>>>>configurations file in CLICKDIR/conf/ directory.They helped to
> >>>>>>>>>>understand
> >>>>>>>>>>>>the click.Thanx!!
> >>>>>>>>>>>>
> >>>>>>>>>>>>I am thinking of modifying this configuration file to work for
> >>me.
> >>>>>>But
> >>>>>>>>i
> >>>>>>>>>>>>need to understand basic functionality of click router. I read
> >>>>docs
> >>>>>>>>on
> >>>>>>>>>>>>click router project page and thesis presented by eddie and
> >>>>others.
> >>>>>>I
> >>>>>>>>>>>>understand some asects of this configurations file but need
>some
> >>>>>>help
> >>>>>>>>>>with
> >>>>>>>>>>>>this one to understand it better. IF needed i can copy the
>whole
> >>>>>>>>>>>>configuration file which i am using.
> >>>>>>>>>>>>
> >>>>>>>>>>>>Please suggest as it will help to write my own configuration
> >>file
> >>>>>>for
> >>>>>>>>>>click
> >>>>>>>>>>>>router.
> >>>>>>>>>>>>
> >>>>>>>>>>>>
> >>>>>>>>>>>>Thanx,
> >>>>>>>>>>>>Gaurav
> >>>>>>>>>>>>
> >>>>>>>>>>>>_________________________________________________________________
> >>>>>>>>>>>>Is your PC infected? Get a FREE online computer virus scan
>from
> >>>>>>>>McAfee?
> >>>>>>>>>>>>Security.
> >>>>http://clinic.mcafee.com/clinic/ibuy/campaign.asp?cid=3963
> >>>>>>>>>>>>
> >>>>>>>>>>>>_______________________________________________
> >>>>>>>>>>>>click mailing list
> >>>>>>>>>>>>click at amsterdam.lcs.mit.edu
> >>>>>>>>>>>>https://amsterdam.lcs.mit.edu/mailman/listinfo/click
> >>>>>>>>>>>_______________________________________________
> >>>>>>>>>>>click mailing list
> >>>>>>>>>>>click at amsterdam.lcs.mit.edu
> >>>>>>>>>>>https://amsterdam.lcs.mit.edu/mailman/listinfo/click
> >>>>>>>>>
> >>>>>>>>>_________________________________________________________________
> >>>>>>>>>Get fast, reliable Internet access with MSN 9 Dial-up ? now 3
> >>months
> >>>>>>>>FREE!
> >>>>>>>>>http://join.msn.click-url.com/go/onm00200361ave/direct/01/
> >>>>>>>>>
> >>>>>>>>>_______________________________________________
> >>>>>>>>>click mailing list
> >>>>>>>>>click at amsterdam.lcs.mit.edu
> >>>>>>>>>https://amsterdam.lcs.mit.edu/mailman/listinfo/click
> >>>>>>>
> >>>>>>>_________________________________________________________________
> >>>>>>>Get fast, reliable Internet access with MSN 9 Dial-up ? now 3
>months
> >>>>>>FREE!
> >>>>>>>http://join.msn.click-url.com/go/onm00200361ave/direct/01/
> >>>>>>>
> >>>>>>>_______________________________________________
> >>>>>>>click mailing list
> >>>>>>>click at amsterdam.lcs.mit.edu
> >>>>>>>https://amsterdam.lcs.mit.edu/mailman/listinfo/click
> >>>>>
> >>>>>_________________________________________________________________
> >>>>>Get fast, reliable Internet access with MSN 9 Dial-up ? now 3 months
> >>>>FREE!
> >>>>>http://join.msn.click-url.com/go/onm00200361ave/direct/01/
> >>>>>
> >>>>>_______________________________________________
> >>>>>click mailing list
> >>>>>click at amsterdam.lcs.mit.edu
> >>>>>https://amsterdam.lcs.mit.edu/mailman/listinfo/click
> >>>
> >>>_________________________________________________________________
> >>>MSN Toolbar provides one-click access to Hotmail from any Web page ?
>FREE
> >>>download! http://toolbar.msn.click-url.com/go/onm00200413ave/direct/01/
> >
> >_________________________________________________________________
> >Get fast, reliable Internet access with MSN 9 Dial-up ? now 2 months
>FREE!
> >http://join.msn.click-url.com/go/onm00200361ave/direct/01/
_________________________________________________________________
Express yourself instantly with MSN Messenger! Download today - it's FREE!
http://messenger.msn.click-url.com/go/onm00200471ave/direct/01/
More information about the click
mailing list